The Design Of Full Front Slippers

The front part of the front shoe for the slippers should be wrapped around the toe and sole. Therefore, the thickness of the shoe last is required, and a special full leather slipper should be selected.

Men's type 250 and two half full leather slipper are compared with the same type of prime last. The length of the last bottom is the same, but the design of the rear body is more fat, similar to all air sandals. The tolerance is 4mm, the heel is broad and the supporting ability is good.

Among them, the last metatarsal circumference is 243mm, which is larger than that of prime head last 3.5mm, and the last surround 255mm is 11. 5mm larger than that of vegetarian head last.

The shoe cavities of the front slippers are relatively large, so as to create a comfortable and comfortable environment for the feet.

Obviously, wearing such slippers is not suitable for long walks, nor is it for fashion shoes, but for indoor wear.

Compared with the same type of prime shoe last, ladies' 230 and one half full leather slippers last the same length, the last metatarsal circumference is 3. 5mm, the last exposed circumference is 11. 5mm, and the rear tolerance is small Imm.

It is also a slipper with loose shoes, large heels and suitable for indoor wear.

The method of making half panels for slippers is to handle long sandals with all air sandals.

The design points of the slippers are mainly used on the V points and E points on the instep, as well as the H, F and P points at the bottom.

The length of the front part of the slippers is different from that of the front ones.

As shown in Figure 4-5-1, this is the three basic structure of full front slippers. The short front is usually taken near the V point, and the long front is taken near the E point. The middle length front is taken near the convex point of the front tarsal bone, and the length of the bottom mouth is connected smoothly.

The design of the long front and middle front needs to be handled with a seesaw.

Notice that the E points of the last man and the woman take 27% of the foot length.

 

In addition to indoor leather slippers, disposable bathing slippers in hotels, suitable for winter wear cotton slippers and so on, is also a basic application.

The full pair of fashion slippers is the evolution of Bora's variant products on the basic structure.

1. the design of the shallow front full front ladies slippers.

As shown in figure 4-5-2, the front shoe of the shoe is similar to that of the shallow shoe, and the front door is located at the front, and the foundation structure belongs to the short front type.

If the front arm is too short and the ability to keep up with the foot is poor, a lengthening part bar is also designed at the E point.

The extension bar belongs to the front part, but occupies the position of the rear side.

 

In the structural design, the operation process is similar to the design of the female shallow shoe.

The bottom parts of the slippers are required to be processed.

Design of 2. gallbladder full front ladies' slippers

As shown in figure 4-5-3, the front part of the shoe is made up of half round bars and shoe gallbladder. There are three eye positions on the tongue. The tongue length is in the vicinity of the front West bone bump, and the foundation structure belongs to the middle long front type.

 

In the design of the structure, we first design half girth parts, and then take the double line to take the stilts, then design the shoe gallbladder and copy the outline.

The operation process is the same as the opening structure design of the full shoe.

3. design of women's slippers with full front cover

As shown in figure 4-5--4, the front part of the shoe is made up of round bars and shoe covers, and the shoe covers are pressed on the round bars and have a "V" shaped false line for decoration.

 

In the design of the structure, it is necessary to prepare the replica board, first use the double line to pick up the outline of the shoe cover, then reproduce the contour line of the contour strip, which is the same as the design process of the shoe cover shoe.

Double line pick up is the comprehensive use of natural stilts, changeover and craft seesaw. The half panel with long stilts only solves the problem of natural stilts, so when designing slippers and sandals with a cover, they still use double line pick up.

When designing the full front slippers for fashion type, you should use full complement sandals last to ensure the circumference and ensure the shape of the toe.